2500 Series | Safety Relief Valve
BelGAS CP Control Products
The BelGAS CP 2500 Series Safety Relief Valve is a high-performance, ASME-certified pressure relief solution engineered to protect vessels and piping systems from overpressure conditions. Designed for both gas and liquid service, it delivers dependable, repeatable relief performance across a wide range of operating pressures.
Built for oil and gas environments, the 2500 Series combines rugged carbon steel construction with corrosion-resistant stainless steel internals, ensuring long-term durability and consistent operation in demanding field conditions. Each valve is manufactured and tested in accordance with ASME Boiler and Pressure Vessel Code Section XIII and certified by the National Board, providing assurance of performance, safety, and compliance.
With multiple orifice sizes, spring ranges, and configuration options available, the 2500 Series can be tailored to match specific system requirements while maintaining precise pressure control and high flow capacity.
Typical Applications:
Separators, pressure vessels, heater-treaters, compressors, gathering systems, transmission lines, meter runs, and general oil and gas production equipment
Key Features
- Available in 1” and 2” valve sizes with multiple inlet configurations
- Wide spring range coverage from low-pressure to high-pressure applications (15–2500 PSIG depending on configuration)
- ASME Section XIII and National Board (NB) certified for safety and compliance
- High flow capacity design for efficient pressure relief
- Multiple orifice sizes (C through G) to match required flow characteristics
- Soft seat trim for improved sealing and reduced leakage
- Carbon steel body with stainless steel internal components for corrosion resistance
- Designed for both gas and liquid service applications
- FNPT outlet and MNPT inlet connections for standard integration
- Optional gauge port configuration available
- PERFORMANCE ADVANTAGES
- CERTIFIED PRESSURE RELIEF YOU CAN TRUST
PERFORMANCE ADVANTAGES
Why the BelGAS CP 2500 Performs Where It Counts
PRECISE RELIEF CONTROL
Engineered with optimized orifice sizing and spring configurations, the valve delivers high-volume flow while maintaining accurate set pressure control. This ensures efficient system protection without unnecessary pressure fluctuations.
BUILT FOR HARSH OIL & GAS ENVIRONMENTS
With a carbon steel body and corrosion-resistant stainless steel internals, the 2500 Series is designed to withstand demanding field conditions, including pressure cycling, temperature variation, and exposure to corrosive media.
CONFIGURATION FOR MULTIPLE APPLICATIONS
The selection matrix allows customization across valve size, orifice size, spring range, and service type. This flexibility ensures the valve can be properly matched to both low-pressure and high-pressure systems across gas and liquid applications.
RELIABLE SEALING WITH SOFT SEAT DESIGN
The soft seat trim improves sealing performance and minimizes leakage, even after repeated operation. This enhances system efficiency and reduces maintenance requirements over time.
Not what you are looking?
Similar Products to the 2500
P4000 Mechanical Dump
Mechanically operated dump valve opens to discharge accumulated liquid when a rising float lifts the internal lever mechanism.
P4100 Fuel Gas Control
Pneumatically operated control valve throttles fuel gas flow in direct response to changes in the applied control signal.
P4200 Treater Dump
Dump valve opens to discharge media from the vessel when the connected level controller signals
a rising level.
P4500 Motor Valve
Diaphragm-operated control valve strokes balanced trim as the pneumatic signal shifts, holding stable at low pressures.
P5300 Back Pressure
Back pressure regulator opens against spring force to relieve excess flow and hold upstream pressure at the setpoint.
P5350 Pressure Reducing
Pressure reducing regulator throttles flow to hold downstream pressure at setpoint, opening as demand rises.
P5400 Control Valve
Direct-acting control valve senses upstream pressure and opens to relieve flow, maintaining a steady back pressure setpoint.
P5500 Control Valve
Direct-acting control valve uses balanced diaphragm trim to hold back pressure steady as upstream flow and pressure vary.
P7100 HP Control Valve
Pneumatically operated control valve modulates high-pressure flow in direct response to the applied pneumatic control signal.
P7200 HP Control Valve
Pneumatically operated control valve strokes to throttle high-pressure flow as the pneumatic control signal changes.
P7200PB HP Control Valve
Piston-balanced control valve offsets process pressure across the trim, allowing stable high-flow control with less actuator force.
P7300 Non-Freeze Dump
Dump valve isolates the trim from the pressure drop during discharge, preventing freezing that cooling would cause.
P7400 Non-Freeze Dump
Pneumatically controlled dump valve discharges liquid on signal while its trim design prevents freeze-up.